Introduction
This power combo consists of Skylord 40A ESC and Tomcat TC-G-3520-KV980 (G15) motor. It has the advantages of strong power, precisely controlling, rapid response and etc.
Features
Skylord 40A ESC
- Microprocessor in the ESC is powered by separate voltage regulator IC, with better anti-jamming capability, greatly reducing the possibility of out of control.
- The throttle range can be configured, fully compatible with the available transmitter. The ESCs have smooth and accurate speed control, and excellent throttle linearity.
- The highest motor speed: 210000 RPM (2 poles), 70000 RPM (6 poles), 35000 RPM (12 poles).
- Support three start modes, Normal, Soft and Super-soft. Normal mode is suitable for fixed-wing aircraft. Soft and Super-soft modes are suitable for helicopter.
- The ESC has full protection features such as low voltage protection, over-heat protection, over-load protection, and throttle signal lost protection, it can effectively extend the service life of the ESC.
- Support multiple programmable items which could meet more users' need.
- A 3-in-1 programming card with a very small size and intuitive interface can be purchased additionally for easily programming the ESC. It brings much more convenience for users than transmitter.
Tomcat TC-G-3520-KV980 (G15) motor
- The motor is made of high-strength aluminum alloy casing which can greatly strengthen the impact resistance.
- The winding uses 240℃ heat-resistant magnet wire after the vacuum impregnation treatment, which can improve the heat conduction and heat resistance, prolong the service life of motor.
- Special bearing imported from Japan is wear proof. It still provides smooth high-speed rotation after using for a long time.
- N45H magnet is hard to degauss even in the high temperature and can guarantee the reliable high torque output.
- Optimized design provides high efficiency way for dissipating heat, which gives the capability of consistent high power output.
- Through the handling of dynamic balancing, Tomcat motor can lower the vibration and noise during the motor’s high-speed rotation.
Specifications
Skylord 40A ESC
Model | Cont. Current | Burst Current (10s) | BEC Mode | BEC Output | BEC Output Capacity | Battery Cell | Weight | Size (L*W*H, unit: mm) | ||||
2S Li-Po | 3S Li-Po | 4S Li-Po | 5S Li-Po | Li-Po | Ni-MH | |||||||
Skylord-6A | 6A | 8A | Linear | 5V/1A | 3 servos | - | - | - | 2 | 5~6 | 5.5g | 32*12*4.5 |
Skylord-12A | 12A | 15A | Linear | 5V/2A | 5 servos | 4 servos | - | - | 2~3 | 5~9 | 10g | 38*18*7 |
Skylord-15A | 15A | 20A | Linear | 5V/2A | 5 servos | 4 servos | - | - | 2~3 | 5~9 | 17g | 48*23*6 |
Skylord-20A | 20A | 25A | Linear | 5V/2A | 5 servos | 4 servos | - | - | 2~3 | 5~9 | 20g | 42*25*8 |
Skylord-30A | 30A | 40A | Linear | 5V/2A | 5 servos | 4 servos | - | - | 2~3 | 5~9 | 38g | 65*25*12 |
Skylord-40A-UBEC | 40A | 55A | Switch | 5V/3A | 5 servos | 5 servos | 5 servos | - | 2~4 | 5~12 | 42g | 65*25*12 |
Skylord-50A-UBEC-3A | 50A | 65A | Switch | 5V/3A | 5 servos | 5 servos | 5 servos | - | 2~4 | 5~12 | 42g | 65*25*12 |
Skylord-50A-UBEC-5A | 50A | 65A | Switch | 5V/5A | 8 servos | 8 servos | 6 servos | - | 2~4 | 5~12 | 42g | 65*25*12 |
Skylord-60A-UBEC | 60A | 80A | Switch | 5V/5A | 8 servos | 8 servos | 6 servos | 6 servos | 2~6 | 5~18 | 62g | 77*35*14 |
Skylord-80A-UBEC | 80A | 100A | Switch | 5V/5A | 8 servos | 8 servos | 6 servos | 6 servos | 2~6 | 5~18 | 80g | 86*38*12 |
Skylord-100A-UBEC | 100A | 120A | Switch | 5V/10A | 12 servos | 12 servos | 10 servos | 10 servos | 2~6 | 5~18 | 74g | 70*30*20 |
Tomcat TC-G-3520-KV980 (G15) motor
Type: TC-G-3520-KV980 (G15)
KV(rpms per volt):980
No load current: 2.2 A @10V
Resistance: 0.033 ohms
Watts: up to 440
Continuous Current: 32A
Max Burst Current: 43A,10seconds
Cells: 3–4 S Li-Po
Recommended Props: 10x6 to 13x6.5
Slots,Poles: 12,14
Diameter: 35 mm
Shaft: Diameter 5.0 mm
Weight: 145 g
Brushless ESC: 50A
Copyright © 2009-2019 DetrumTech, Co,.Ltd All Rights Reserved
